Leaking Clothes Washer?

If the seals are shot on my washer pump, will it leak when the washer is not running, or only when it is running?Leaking Clothes Washer?
The pumps will only leak under pressure when washing and disbursing the used water out of the drain hose. If the leak is continuing when washer is not in use then there is a bad hose connection or split hose is another problem.





The other is it could be the spindle seal of the agitator could also be worn out and this can be detected if there is any oil mixed in with the water on the floor.





If you cannot fix it yourself then get a repair person to fix the problem.Leaking Clothes Washer?
IF not hoses, it is cheaper to purchase a new machine than having one repaired...make sure the delivery company will haul off the old machine. good luck

worms

Windshield washer cap?

The cap to my windshield washer on my vehicle snapped off. Will this harm my car?Windshield washer cap?
You will start getting some dirt in the fluid which, in time, might clog the system. Cover the opening with something, even saran wrap.Windshield washer cap?
Only if you lost the cap. If not simply put the cap back on and it will not harm anything

Windshield Washer Pump not Working.?

My vehicle is having troubles with the windshield washer pump. When i pull the lever there is no pumping sound or water being sprayed onto the windshield, tho the wipers still work. I've already tested the wiring and all is fine. The problem appears to be either the pump itself or a free floating wire.





The unnconnected wire is apart of a set that goes into a plug beneath the washer reservoir. My guess is the wire came disconnected from the plug and requires reattchment. My problem is when i go to strip the wire sheeth expecting to see some silver or copper looking wire underneath, what i actually get is more white-green lithium-like paste within the wire. Ok wheres the actual wiring for me to connect back to the plug?





Perhaps this is normal and the wire does not require reattaching? In such a case I'd have to conclude the pump is to blame. Any ideas on how i can also test the pump and even replace it if necessary. It seems fixed to the reservoir somehow.





TxWindshield Washer Pump not Working.?
Take it to a mechanic or the dealership and have them either fix it or replace the pump. Better to have a professional do it and not have it screwed up.Windshield Washer Pump not Working.?
that wire to me sounds like the problem.The reason it has become disconnected is because it has corroded and turned to the paste.If need be pull the pump off and see if there is a wire missing.Chances are it is.and if it is check if the wire that is still conected is a positive or a negative.If its a posi then make a lead up to go to the plug to an earth to the chasis.

95 civic washer fluid problem......?

When i hit the signal, there's no washer fluid, and also no noise at all. I've read others question about the problem and the problem seems to be a bad pump or fuse. Where do i find the pump? and which fuse is it? How would i know if a fuse is burned out?95 civic washer fluid problem......?
the pump to your washer will be underneath the bottle that you fill, the fuse will most probably be in the fuse box it should be marked on the lid of the fuse box,if it is not then you will have to pull each fuse in turn and have a look at each one ,the fuse as a metal strip running through the centre of it if it has blown then the strip will be broken replace that,that has blown.95 civic washer fluid problem......?
your fusebox should be under the hood. pop the lid off and look at the diagram it will show you. it should say WASHER OR WASH. pull the fuse out...if there is nothing in the middle of the 2 terminals, its blown. replace it with same size. most fuse boxes have spare fuses in them.


or it could be the pump but check fuse first. some times the pumps get gummed up with dirt. on some cars the pump is located on the resevoir.

I put my ipod through the washer. anyway it will still work? what can i do?

ipod touchI put my ipod through the washer. anyway it will still work? what can i do?
My brother did this and his I Pod never worked again. I guess it depends on what kind of luck u have.

My phone just went through the washer...?

Its a Motorola SmartPhone....someone told me to put it in the freezer....


Any sugestions?My phone just went through the washer...?
uhh..put it in riceMy phone just went through the washer...?
put it in the dryer, but not for too long. that happened to my sisters phone and it ended up being fine
leave in your back seat of your car for a few days in the hot sun. this should dry it out.
Do not put it in the freezer!





Put it in a ziploc bag of uncooked rice for a couple days, then leave it in the sun for a couple more days... That's really your only hope. Unless you feel comfortable taking it apart but be careful of the static.
immediately take the battery out. Let it sit for a few days, you can try using a hair dryer on it or putting it in a bag of uncooked rice, or if you have packets of silica gel (they come with new shoes and sometimes in vitamin bottles) or other desiccants, those work too.
Take the battery out, submerge it in a bowl of dry, regular, rice. Put it in a warm spot ( sunny window) for a couple of days. Make sure all the condensation is gone before you put the battery back in and turn it on.

Disk Washer Method Calc homework. Please help Im stuck?

Using the disk/washer method write the volume of the solid obtained by the region enclosed by y=x^(1/2), x=4 and y=0 about the y-axis as a definite integral. Do not evaluate the integral!!! Please helpDisk Washer Method Calc homework. Please help Im stuck?
Yeah, you could do it that way. But there's a much easier way.


It's known as the shell method, and by adding up an infinite number of shells made by this region... we can find the volume of the figure.


Imagine a shell, looks like a cylinder, but it's hollow. Think of what what would happen if you wanted to find the volume of that shell. You could cut it right down the middle and add up the volume of a rectangular prism: (Length)(Width)(Height/Thickness). The length is the circumference of the rotation, or 2蟺(r)... or what's on top - what's on bottom.


In this case, the function on top is x^(1/2), and that on bottom is 0. So, top - bottom is x^(1/2) - 0.


Let's setup our integral


2蟺鈭?x^(1/2)-0)(width)(height/thickness鈥?br>

Remember, the length is the circumference.


The width is the distance from the of rotation to the farthest point right. Well, in this case it would be 4, but it's necessary to call the out most part x. The width is always achieved by right - left. Or x - 0, remember the y axis is really x=0.


Substitute our width into the integral:


2蟺鈭?x^(1/2)-0)(x-0)(height/thickness)


That leaves our height/thickness, and the only thing left is our dx... because we're adding up an infinite number of these shells. The one point represents each shell we add up. In addition, our bounds would be from x=0 to x=4... just like if you were to slice a cross section perpendicular to the x-axis.


So...


2蟺鈭?x^(1/2)-0)(x-0)dx from x=0 until x=4.


I know it's a little confusing, but if you need any more help please feel free to give me an IM or email at sparta308@yahoo.com.

worms

Bengali car-washer man has throat constriction; feels pain even when swallowing fluids?

had chest congestion before but that is better now; chronic problem since 2 years; may have some fluid filled abcess in trachea. Please provide a lasting and sure remedyBengali car-washer man has throat constriction; feels pain even when swallowing fluids?
Homeopathic Treatment :-


I suggest he should take the remedy BELLADONNA in 30, three times a day half hour before meals. To read more about the remedy please click the link below :- http://homeoint.org/books/boericmm/b/bel鈥?/a>


And please keep me posted about his progress after taking the suggested remedy for three days at least.





Take Care and God Bless !Bengali car-washer man has throat constriction; feels pain even when swallowing fluids?
Since you mentioned the chest congestion, were you on antibiotics before you noticed the difficulty swallowing? Sometimes, antibiotics will cause Candida esophagitis. If that's it, and you can't go to a gastroenterologist, try eating yogurt. There's other problems that make swallowing difficult, so it would really be best to see a gastroenterologist for a definite diagnosis and treatment.

Can you put plastic plates in the dish washer?

Yes you can! I do it all of the time! :-DCan you put plastic plates in the dish washer?
hard plastic plates can be placed in the dishwasher , however , disposable plastic plates may meltCan you put plastic plates in the dish washer?
Yes; the water is not hot enough to melt them but keep the Dryer off because that is hot enough to melt anything plastic.


And what a mess to try and clean.

My iPod nano 3rd gen. went through the washer...how long do i let it dry out?

will it work again...i can't believe i did that...it was in my pocket and i washed my pants...it had a case on tho, not a silicone case, but a leather one...do u think it may be okay (even if i plugged it into my computer)My iPod nano 3rd gen. went through the washer...how long do i let it dry out?
It's down to a few things, really. How long it was in the washer, how hot the wash was, how thick (and waterproof) the case was and quite a bit of luck.





It's usually a good bet to take it apart as much as you can, and let everything dry separately, as this makes it most likely that it'll survive. I'd leave it for about a week, though sometimes even longer is better.





If any of the circuits have shorted though, it might not work even when it is dry.





Hope it works!My iPod nano 3rd gen. went through the washer...how long do i let it dry out?
I just did the same thing to my I pod nano 3rd generation, just yesturday, completely through the wash and dryer. This is the key, let it dry in a dry warm place for a few days, with all luck it will work. The reason behind this is because technically the i pod is always on unless it is left idle for more than about 48 hours, this is because the clock keeps running. If you notice your i pod start up with the apple logo ever it is because it has been left off long enough to completely turn off and is now restarting. Because it is such a small decieve it is lucky to use 5 volts max and that is not near enough to fry it with water, furthermore i pods are built to take a little bit of distress and most likely the main boards are sealed and protected. If you can't get it to work by the button try plugging it into the computer that is what i did. Unfournatly your screen may never be the same and show signs of being wet or a little blury but it should work just fine! the only thing different you will notice is that the clock will have been reset.
omg! my friend did the same thing to her ipod!! so she left it on her heater for a week then it worked!! but the screens a bit funny, you have to look at it from a certain angle :P


just make sure you dry it out and it might just survive
4 about 15 mins
put it in the sun wai a few days

Sent my ';LG Chocolate'; cell phone through the washer and dryer,?

I know, bone headed move but too late now to correct the mistake. Is there any hope for this phone at all or is it toast. I took it apart and everything is dry. I'm guessing a chip got fried or something. Anyone else ever save one after water exposure?Sent my ';LG Chocolate'; cell phone through the washer and dryer,?
Once in awhile you can get lucky. I seen a phone get washed and then work days later. I haven't seen one go through washer and dryer though. :(


If you have insurance then it will be covered. a $50 deductible will be all the will cost to replace the phone. If you don't have insurance then replacing it for the same phone will run you about 299.99 . If you don't have insurance I would browse ebay for a replacement if the 299.99 price for full retail is too steep.Sent my ';LG Chocolate'; cell phone through the washer and dryer,?
I dropped my 5300 in a drink and it dried out, but the screen was flawed. Also, what everyone else had said was dead wrong. If you have insurance, it does not cover water damage. Dry it out with a hairdryer, and you might have a chance but its unlikely.
Was unable to save the chocolate. And if you're moisture stickers are ruined, hope you got the insurance. Costs 50 to replace the phone but that's the only option.
Sounds like it is toast to me, insurance will proably not cover the replacement either. Mine didn't when it was dropped into the drainage ditch at work and got water logged.
Is it still work? I hope it wasn't on and then it would have been fried.. but maybe at the most to replace a piece or two..
Even if you can get the power on, the minerals in the water will render the keys useless in a short while. Expensive mistake, there.

Return Washer to Lowes...?

Do you know what the time limit is and any other requirements?





Thank you!Return Washer to Lowes...?
Retailers generally will not accept returns/exchanges on big ticket items. They will tell you to call the Manufacturers Repair dept for assistance. The manufacturer is responsible for warranties. Good luck:)Return Washer to Lowes...?
30 days
90 days-is normal
Do you have a warranty? Call and tell them it's broke, if they say too bad, talk to their manager. You MUST be pushy, as they don't really want to replace or fix anything. Usually if you are persistent they will give in.
my mom returns anything anywhere anytime trust me they will take it back.
call Lowe's and ask them. I work there and some thing they return anytime some thing have to have a manufactures number attached.

Which is better gas or electric power washer?

gas by a mile,more power,more mobilityWhich is better gas or electric power washer?
Gas!

worms

Frigidaire washer make noise and smoke on spin cycle. clear liquid on floor not water?

Never good for smoke to be coming from a washer...; )...i would say that 1 of 2 things is happening...eithor your electric motor has gone bad and its getting hot enough to burn the windings inside....or 2...your gearbox is bad / seal in the gearbox is bad leaking oil onto something hot (maybe the motor) causing the smoke and clear liquid (oil) on the floor...touch the clear liquid and rub it between your fingers...if its slippery then its oil....Frigidaire washer make noise and smoke on spin cycle. clear liquid on floor not water?
How old is this washer?

Smelly washer???

I dont know if anyone has had this happen before, but, I wash a load of laundry and then put it in the dryer...but when the clothes come out they have a bad smell! What would be causing this and how do I get rid of it?? Is it the washer? The dryer? They dont smell clean! I dont get it.Smelly washer???
I too would run a cycle with just vinegar or bleach and no clothes. Also, don't over load the washer or dryer with clothes. If your loads are too large the clothes will not swish and get clean in the wash. Then you put them in the dryer and they didn't get clean, that too would cause your clothes to not smell clean. On super dirty loads of wash, add some baking soda or Oxi-Clean to the water. That too will cut down on the smell and give your detergent a boost.Smelly washer???
Run an empty load with a cup of bleach only in the washer, set it for large/full load and hot water.


That should clean up the washer.


I'm not sure about the dryer, if thats where the odor is, you may need a pro if its gas, and your clothes smell like gas, or , if its electric and smells burnt, then you may have something on the heating element. If it neither smells like burn or gas then try a fabric softener sheet in the dryer and see if that helps.
I don't know what it is but if it is the washer I hear you are suppose to do a cycle with no cloths and put lemon juice in it....I never done it before but I hear it works!!
i have the same problem.this is the first front load washer i have had in 35 years.if i only could have my old one back! i use everything.sometimes vinegar,boraxo,soda,bleach and amonia.it's really the pits!!! my daughter just got the red LG set from lowes in April for $2,000 and has the same problem.leaving the door ajar doesn't do any good.
When washing your clothes add 1 cup of plain white vinegar in with the soap, and leave the lid open when you take the clothes out. so moisture doesn't start to make it smelly.
I would try running it empty with baking soda in the water. That usually gets rid of evil smells.

Are womans status equivalent to a dish washer and a oven?

i personally think this statement to be trueAre womans status equivalent to a dish washer and a oven?
LOL





SEXIST PIG





what are men good for???





NOTHINGAre womans status equivalent to a dish washer and a oven?
I would say no cause you need a dish washer for the dishes and you need oven for the cooking you need but probley in the olden days they would yes to your qustion
I will have to agree, they always have to clean up after there man and most always have a bun in the oven, lol
Yeah - definitely. Don't forget the iron, refrigerator and vacuum cleaner too....
Are you Jason C Sandstorm in a different guise? I don't believe I will dignify this question with a response. ;-(
haha gosh... ok... and how would you feel if we say that a guys status is equivalent to a lawnmower and a pile of rubbish bags?
I object.


They are mothers, sisters, lovers and friends... and most of the tiem they are better friends than men cos its easier to have heart-to-heart conversation with them...
When did Jason Sandstorm become the son of God?
And we are not that bright either...
Yes
you're a man, your status is a pile of sh*t
that is the status the male gender give us.

The washer machine is shaking and we didnt turn it on?

im really scaredThe washer machine is shaking and we didnt turn it on?
call the maytag man.The washer machine is shaking and we didnt turn it on?
it's either a pressure buildup in the water lines or a defective switch
Grab the camera..ghosts don't like it when you film them..even so, something needs to be filmed, heee,hee
Better make sure a family pet didn't jump in there.
Open the lid and rebalance the load.
let ur pet out......!!
Turn off the washing machine!!


I'm scared too!!! lol


Edit. Maybe you're cat or dog is inside it. Please check !


333..Good Idea ...I had one of those ';belts'; one time ..but it made me itch when I shook. You could put a cushion on the washer %26amp; it would be a vibrating ';Lazy Boy'; chair! (or ';Lazy Girl'; chair in our cases! lol)
quick!!!...go fetch either a medium or a priest , lol
Feed it your laundry. It's telling you it's hungry.
LET THE CAT OUT!!!!!
You know what they say about shaking washing machines dont you......LOL you sit on them....sorry couldnt resist, they were talking about that on the moring show a couple of days ago....People put their washing machines on spin cycle to sit on them......Everytime i go past your question i cannt help think that, and what they were saying about it on tv.....lol
its a ghost washing their white load
It is my opinion that is is not paranormal. Most likely you have air in your water lines causing a pressure buildup. Cut it on like you are going to wash a load of clothes and see if that won't fix your problem.
someone who used to live in your house killed your washing machine and now its back to haunt you





lol jks


sometimes water clogs up and like releases which causees it to shake, or theres an electric problem


dont worry about it :)
Run Away
Bang on it and see if it shakes more, there might be something that crawled inside, if not then you should unplug it asap and take a look at it, because something can be wrong with the electricity and you dont want anything to happen.

Maytag washer - pump?

Does anyone have any information on how to replace a pump on a Maytag washing machine (model SAV4655EWW). This is the second time in a year (machine's only 2.5 years old) that I have to replace the pump and I refuse to call the lonely repair guy again - he can't come out for a week anyway (not so lonely is he - busy replacing Maytag pumps probably) Any help would be appreciated.Maytag washer - pump?
I believe the model you are referring to has a removable panel in the front, 2 hex head screws remove the panel. The pump should be on the bottom of the motor. Not hardly as easy to change as a light bulb but can be done by do-it -your-selfer with some mechanical skills. Have to remove three screws from pump from bottom (which is the hard part) and pull off motor. Reverse procedure to install new pump. Make sure pump isn't clogged before replacing or other similar problem.Maytag washer - pump?
Its almost as easy as replacing a light bulb. You ll need to access the part of the washer were the pump is,usually at the bottom,remove belt,unclamp the hoses to the pump, remove the screws holding the pump and remove pump,installation is the reverse and voila! Second time huh? Sometimes they get clogged with to much lint or pet hair so that's why they stop working! Well maybe not as easy as replacing a light bulb but its not hard at all!
Before attempting a repair make sure you turn off the power The pump will have two electrical connections, check that are still connected, they have been known to vibrate off.

My dryer on my bosch classixx washer dryer, has stopped?

the washer works fine, just the dryer dosnt dryMy dryer on my bosch classixx washer dryer, has stopped?
Greetings,





Hope this link works for you!





S1lent





http://www.retrevo.com/d/ds/progress?doc鈥?/a>

worms

How can i change the cranking rope in a honda gas pressure washer 13.0 ?

If you can still get to the rope good take the pull off the motor pull the rope out carefully not to let the coil spring fly out (it not easy to do)attach the new rope were you dug out the knot and rap it around sick through the pull hole and add the handle. good luck ..................


If the rope broke you have to do the same as above but re coil up the coil spring the attach the new rope and rap it around sick through the pull hole and add the handle.How can i change the cranking rope in a honda gas pressure washer 13.0 ?
This might be long winded, but hang in there.





Remove the recoil housing and be very careful not to remove the recoil pulley wheel, you won't have to do this at all. Purchase a sever foot piece of recoil rope which you can obtain from pretty much any hardware store, but take your old rope with you for size.


NOTE: Use a recommended recoil rope, not just any nylon that you think might work.





After you get your recoil removed, lay it out flat on a table, and remove the old rope, now take your new rope, and using your index finger, wrap the rope two times and tie it into a knot, a really tight knot, leaving a small little tip sticking out, now the next part you are going to have to be very careful not to get burnt, take a lighter and burn the end of the rope until it starts to melt, and then push it flat either using the concrete floor or on the work bench.





On the other end of the rope, melt the other side of the rope and using a shop rag, rap the rag and pull straight out, this will make the end of the rope stiff which you are going to need.





Take the recoil, if this has the knot stop on the bottom of the pulley, you really need to pay close attention to how you remove the pulley, leave it flat on the table and remove the lock bolt, and it will pull up rather easy, but when doing so make sure to try to keep the spring in place, in most cases it will stay, but remove the pulley and run the pointed end of the rope through the pulley, so that the knot is in the area it should be. Replace the pulley, and whined the recoil, until the spring is tight and you cannot go anymore, then go a 1/4 turn back, and run your rope through the hole, and let the recoil wrap the rope for you. tie a slip knot, install your pull handle and you are all set.





If your knot stop is on top of the recoil you will not have to remove the pulley at all just wrap it like I told you in the end.





Good Luck!

How do you fix a dish washer. it won't do an thing? power is on.?

HOW OLD IS IT. PROBABLY A BAD DOOR SWITCH. DON'T FORGET YOU SHOULD HAVE A SWITCH ON THE WALL THAT NEVER GET USED AND THEREFORE GETS FORGOTTEN UNTIL YOU HAVE A VISITOR OR MOMMY'S HELPER WHO SNAPS IT OFF WHEN SHE MEANT TO TURN ON THE DISPOSER?How do you fix a dish washer. it won't do an thing? power is on.?
verify the power is on, then you have to work backward and eliminate each possible problem starting with the latch switch , it all depends on how old it is it may have anywhere from 0 to 30 kill switches built in for safety, like if it dosen't have any water, the drain is plugged ect.if its not too simple though you need to eaither call a repair man or get a new one.

If I'm not allowed to spray the kids with a pressure washer can I at least shock them with a cattle prod?

Just trying to understand this whole parenting thing before they go off to college!








Thanks yahoo...They wanted this for the home and garden section!If I'm not allowed to spray the kids with a pressure washer can I at least shock them with a cattle prod?
rule #1 is don't slap them with your barehand.If I'm not allowed to spray the kids with a pressure washer can I at least shock them with a cattle prod?
just shock them in a place where no one will see the burns!
How about one of those dog collars... that shock..then they'll at least be quiet.
You CAN spray your kids with a pressure washer. I used to do that all the time. They loved it.
the only problem i see with the cattle prod is the burn marks...
Spray them with the pressure washer then go for the cattle prod! You can get one at Tractor Supply. I think there only 40 bucks, well worth it!


-Someones gotta teach em a lesson
cover them with a hood and make them stand naked on the front yard.





if its good enough for the us govt its good enough for the citizens!

How do i fix my washer? we turn the water on and it stop right after. apparently the water has a leak. ?

Sorry not enough details . Close washer ? What stops right after , everything , the water coming in , what ? Resubmit question and give all details .How do i fix my washer? we turn the water on and it stop right after. apparently the water has a leak. ?
Just a guess but either the intake is clogged or not working properly but my best bet is on the timer thingie. It tells everything to work. You need a repairman. If you had a leak, the water would keep coming in and then draining out but the water would run forever because the tub can't fill up. You need to give much better details of exactly what you are doing and then exactly what happens.

I can't get my washer to work! Can anyone help?

I purchased a whirl pool washer three years ago from lowes and now I am having a few problems. The washer will fill up with water but then will not go into the next cycle. A few times I have let it sit for an hour and then pulled back the knob and it worked. However, it is not working now. What do I need in order to make it work?I can't get my washer to work! Can anyone help?
You may need a new timerI can't get my washer to work! Can anyone help?
It looks like a problem specific to your machine. Possible only the timer knob need a change. Honestly.... best would be to call the service centre asap.

If I connect 2 pressure washer pumps to a motor, will I get double the output????? help?

ok here is the situation, I have two 3000PSI pressure washer pumps, and a gas engine, If I took both and connected them to the motor, supplied enough water flow and used a coupler to join the output on both, will I get 6000psi of water pressure or will I end up creating back pressure and possibly damaging the pums, or will I get killed in the process.





I hope someone with an engeniering degree reads this, maybe I can get a valid answer. oh and forgive me for my spelling disaster here....he he heIf I connect 2 pressure washer pumps to a motor, will I get double the output????? help?
Pressure does not add up like that. If both pumps put out 3000 psi then the pressure would be 3000 psi.





If there was a large difference in pressures between the two pumps, you could create some back pressure for the smaller pump, this pump would back up on its pump curve and its output gpm would go down. If it is to great a pressure difference for the pump, the pump could spin or even cavitate which then could cause problems.





But, you have one motor connecting to 2 washers, you might not even get 3000 psi since the horsepower from that motor is being shared since the motor is now seeing twice the load. Check what the motor HP is and what HP is required by each washer.





I think you are safe so far ;)If I connect 2 pressure washer pumps to a motor, will I get double the output????? help?
This question has already been answered. I'm not sure why you keep posting it.

worms

I locked my maytag washer door!!?

I just threw my shoes and some detergent and shut the door, put it in normal and pressed start


it started fine


then It just stopped so I went to go get my shoes out and it says the door is locked and I cant open it!


i TURNED EVERYTHING OFF.


HOW DO i UNLOCK IT!!I locked my maytag washer door!!?
If you still have the book to the washer (and you should always keep these books) just look it up. There should be a way to reset everything.I locked my maytag washer door!!?
I don't know if this will help, but it works on my electrolux washer:





To unlock the control, press the “Options” and “Select” buttons simultaneously. The control lock status light will no longer be lit and the door unlocks.





If this doesn't work call maytag!

Daihatsu Hi-Jet screen washer reservoir/tank.?

Can anyone explain to me how to re-fill it and exactly where it is on the vehicleDaihatsu Hi-Jet screen washer reservoir/tank.?
Its inside around the steering column area. From what i remember on the rascals? Possibly on the passenger side altough still inside.

What is NewClear? Is it some sort of suicider window washer?

I don't understand. Dick and Condi keep on talking about it like it is something scary.What is NewClear? Is it some sort of suicider window washer?
Very close, yer Majesty. It's a uranium powered zit cream.


And it is very scary. The zits clear up, but your head mutates after 6 months.





PS - don't you remember ? We went to Iraq for the orphans of mass erection ?What is NewClear? Is it some sort of suicider window washer?
LOL! you are a riot!
It is a technology that you should use in Iraq. Right after you bring our troops home.

What causes lint in the washer?

We moved into a new house and our clothes out of maytag washer have lint on them and the dryer screen is full of lintWhat causes lint in the washer?
small fibers in the clothing that are comming loose from the fabric weave.What causes lint in the washer?
usually new clothes like shirts or any clothing having clingy fibers that come off in the washer. we have the same problem with our washer and i think its a maytag where the ring around the washer had lint and dust particles. just like when u get lint from dryer. just particles u don't see that come off your clothes. i usually clean the top of the washer with windex and paper towel
You now own a better washer and dryer than before. This is a normal occurrence with a more powerful machine. Just make sure you remove the lint from both machines after every load.

Cat was accidently put in Washer Machine, is CPR possible???

cat is deadCat was accidently put in Washer Machine, is CPR possible???
How could you ';ACCIDENTALLY'; put a cat in a washing machine?Cat was accidently put in Washer Machine, is CPR possible???
I hope this is a joke.
it is but if the cat has been down more than a few minutes it would be futile
I doubt it

Washer smells!!?

My washer has a really weird smell and I have no idea what is causing it... anyone have any ideas on how to get rid of it?Washer smells!!?
Mildew? Run a cycle with no clothes, just extra hot water and a cup of chlorine bleach. When the cycle is complete, leave the washer open until the next time you use it.





If you have a front loading machine, check your owner's manual. These machines are particularly prone to developing odors.Washer smells!!?
well idk how to get the smell out...i think that other guy has a good suggestion about a cycle without clothes...just use bleach/ but a front loader is a washer with a door in the spot of a dryer....if u ever saw ';Stuart Little'; with the mouse..the washer he almost drowns in is a front loader.
Is your cat missing?
It pretty needs a good old cleaning. You can use dish soap with a sponge to wipe it down. You can also use some 409 spray to disinfect. Last you should run it dry with some bleach or Use a detergent that has a nice scent.





A front loader is a wash machine that where the door is in the middle and uses less water and spins at fast speed.





Top loader wash machine is where the door is at the top. They require more water and have an agitator to spin the machine.
take the cat out

worms

What is the program Window Washer, by Webroot Software, Inc.?

This is OK software that cleans traces of your Internet browsing history, cookies, etc.





Why pay for this when you can do it free by deleting the above in Internet Options? Then download the free MRU Blaster. MRU Blaster will securely shred traces of your Internet files/cookies and remove all of your computer's internal records of recently opened documents, etc. I've been using it with great results. Javacool also offers several free spyware and malware utilities.What is the program Window Washer, by Webroot Software, Inc.?
Window Washer is a PC Magazine Editors' Choice winner. Window Washer is the award-winning utility from Webroot Software that washes away your online and offline computer activities, giving you more privacy and greatly increasing your PC's performance. It cleans areas such as the cache, cookies, file history, and Registry items.





Window Washer offers customizable features that let you control what gets washed and what stays. This program also gives you the ability to schedule washes of your system when it's most convenient for you.What is the program Window Washer, by Webroot Software, Inc.?
I have it on my pc from years ago.





It can wash (remove) things on start up or shut down like


Cookies


Run History


Find History


I.E. and other browser History


Temp files


Recycle Bin


.CHK files





oneinsix com
I would google it.

If I connect 2 pressure washer pumps to a motor, will I get double the output????? help?

ok here is the situation, I have two 3000PSI pressure washer pumps, and a gas engine, If I took both and connected them to the motor, supplied enough water flow and used a coupler to join the output on both, will I get 6000psi of water pressure or will I end up creating back pressure and possibly damaging the pums, or will I get killed in the process.





I hope someone with an engeniering degree reads this, maybe I can get a valid answer. oh and forgive me for my spelling disaster here....he he heIf I connect 2 pressure washer pumps to a motor, will I get double the output????? help?
The gas engine is the central component of the whole mess that produces the power. There is no way you can take a gas engine which is capable of producing 3000 PSI and make it produce 6000 PSI. You need more horsepower.If I connect 2 pressure washer pumps to a motor, will I get double the output????? help?
Two 3000 psi pumps connected does not creat a 6000psi pump...Why??? they are both 3000psi . True it may cause a backup and you may lose one of the pumps.





Have a good day. .
I think you risk the possibility of getting killed if you try this one.

I have a question, i have an apt size washer ,my landlord is saying get rid,i pay utilities.?

he saying i cant have it,there's no stipulations in the lease of not being able to have one. there's a leak in the kit.sinki that needs to be fixed,still insist to get rid of it? what can i do.I have a question, i have an apt size washer ,my landlord is saying get rid,i pay utilities.?
You are sure there is nothing in the lease? Do you pay the water bill? How bad is the leak? You could fix the leak yourself and show him the bill and the completed work, he might give you some slack. He might try and give you a hard time because of the water bill. But if there is nothing in the lease even in the small print then just put it away when he is around and try not to wash when he is. There is a way around everything.I have a question, i have an apt size washer ,my landlord is saying get rid,i pay utilities.?
Every county has stipulations on renters and code of conduct. One in the place that I live in states that if there is a leak in the sink due to wear and tear, then the owner/landlord has 1 month to do so. That means if the landlord/owner does not fix the leak then your intitled to get some cash reimbursement or discount off your rent. Find the renters board to see the appropriate steps to get this resolved. They might even fine the owner/landlord for not up-keeping the building. Also they will keep a record on file just in case it goes to court. As for the dishwasher, if your the only one living there then why bother, save on your utilities and keep on washing in the leaking sink. I am sure if you bring this up to the renters board, the board will give him an ultimatum. '; Fix it or we will fine you';.
Read your lease carefully, also research the laws in your state about what he can change. A landlord is able to add amendments to the rules in some states, but he has to give it to you in writing. Is there a clause in your lease that states that he can change or add the rules to your lease?





Otherwise, as long as your rent is on time and there is nothing in the lease, and if you pay the utilities he cannot tell you what to do. Be careful, if it is causing damage to the property, IE water damages ect from the leak and you know about it, he can accuse you of criminal damage to property instead of it being normal wear and tear.





Was the leak caused because of the washer? He may think so. Be prepared to prove otherwise.





Damages are actual things in the apartment that you or your guests actually break - such as a window or a hole in the wall.





Normal Wear and Tear may include things such as faded paint - you yourself did not cause the paint to fade, thus you would not be responsible if and when the landlord decides to repaint.





2.鈥?1) A person who without lawful excuse damages any property belonging to another intending to damage any such property or being reckless as to whether any such property would be damaged shall be guilty of an offence.





(2) A person who without lawful excuse damages any property, whether belonging to himself or another鈥?br>




( a ) intending to damage any property or being reckless as to whether any property would be damaged, and


( b ) intending by the damage to endanger the life of another or being reckless as to whether the life of another would be thereby endangered,


shall be guilty of an offence.





(3) A person who damages any property, whether belonging to himself or another, with intent to defraud shall be guilty of an offence.





(4) An offence committed under this section by damaging property by fire shall be charged as arson.





(5) A person guilty of an offence under this section shall be liable鈥?br>




( a ) on summary conviction, to a fine not exceeding 拢1,000 or imprisonment for a term not exceeding 12 months or both, and


( b ) on conviction on indictment鈥?br>

(i) in case the person is guilty of arson under subsection (1) or (3) or of an offence under subsection (2) (whether arson or not), to a fine or imprisonment for life or both, and


(ii) in case the person is guilty of any other offence under this section, to a fine not exceeding 拢10,000 or imprisonment for a term not exceeding 10 years or both.


** (6) For the purposes of this section a person is reckless if he has foreseen that the particular kind of damage that in fact was done might be done and yet has gone on to take the risk of it.








Good Luck.
If there is nothing in the lease then he can't make you get rid of it, and he is responsible for getting the leak fixed. I would call an attorney for a free consultation to see what legal steps to take. I was dealing with a slum landlord and I call an attorney for a consultation and he helped me out. Good Luck.
If the lease doesn't prohibit it, he can't make you get rid of it, especially since you are paying the utilitities. It isn't costing him anything. You can insist he fix the leaky sink, which is his responsibility, though it can be difficult to hold him to it. It is not a good idea to withhold rent to force a landlord to do something, because doing so is prohibited in some states.


Is there some tenants' rights agency where you are? If so, it would be good to contact them. A lawyer would cost too much and this isn't a big enough problem to justify that expense.

My samsung yp-u2j player got washed in the washer. how do i open it to fix it.?

sorry to say this, but you might want to take it back to wherever you bought it from and ask there... those things are almost impossible to fix by yourself, and you might do more harm than good...

My cellphone was in my jeans and got washed in the washer....?

Yeah haha my mom didnt know i had it in there and washed it... Idkwhat i can do... do you think it will work? It wasnt dripping water...should i leave it sit for a few days or turn it on now..haha i need some help here..My cellphone was in my jeans and got washed in the washer....?
happened to me once. wave bye bye to your phone. It is a gonner.My cellphone was in my jeans and got washed in the washer....?
let it dry, it will take a while for the battery to start working again so give it some time, but if it doesnt get a new one
My son's did too. It dried out and works fine. Hope yours does too.
i would wait a day and then try ...maybe not.

Volume of y=2x(2+x) from [0,2] rotated around y = 4, -2 and x = 4 using washer/ cylinder method?

I am having trouble finding the volume of this shape rotated around each of those axes, can anyone show me how to do this sort of integration?Volume of y=2x(2+x) from [0,2] rotated around y = 4, -2 and x = 4 using washer/ cylinder method?
I have created a graph for you that will take care of the axis is y = 4 case. To see this graph, which you must do or my solution won't make any sense, click on the following link:





http://i369.photobucket.com/albums/oo133鈥?/a>








(1) By Washers





Integrate 蟺 * ((2x / (2 + x)) - 4)^2 as x goes from 0 to 2





For the moment I'm just going to work with ((2x / (2 + x)) - 4)^2





((2x - 4 * (x + 2))^2) / (x + 2)^2





((2x - 4x - 8)^2 / (x + 2)^2 = (-8 - 2x)^2 / (x + 2)^2 =





((-(8 + 2x + -4 + 4))^2) / (x + 2)^2 = [(4 + 2x + 4) / (x + 2)]^2 =





[ (4 / (x + 2)^2) + 2^2]





Now 鈭?((4 / (x + 2))^2 + 4 dx = 鈭?((16 * (x + 2)^(-2) + 4 dx =





16 * (-2) * (x + 2)^(-3) + 4x = (-32 / (x + 2)^3) + 4x





For x = 2 this evaluates to: (-32 / 64 + 8) = (-1/2 + 8) = (15/2)





For x = 0 this evaluates to (-32 / 8) + 0 = - 4





So, not forgetting about the 蟺, we have





蟺 * ((15/2) - (-4)) = 蟺 * ((15/2) + 8) = 31蟺/2.....%26lt;%26lt;%26lt;%26lt;%26lt;....Answer by washers





To be continued

worms

Could someone please tell me where you could find the windshield washer pump motor on a 2001 pontiac gagt1.?

it hasent worked tn three weeks or so. i was thinking that it could mb froze up.Could someone please tell me where you could find the windshield washer pump motor on a 2001 pontiac gagt1.?
The windshield washer pump is located right inside your windshield washer bottle. They started making this a part of the bottle to help them cram more things in. It used to be a part of the wiper motor assembly but not any more. Hope this helps.Could someone please tell me where you could find the windshield washer pump motor on a 2001 pontiac gagt1.?
right at the bottom of the washer bottle.
www.rockauto.com

My whirlpool machine washer wont spin or agitate?

Washing machines, like any other mechanical device, occasionally needs servicing. A common problem with an older washing machine is that the spinner, or agitator, stops rotating during wash cycles. Fortunately, most washing machine problems are easy to troubleshoot. Any do-it-yourselfer can fix it; here's how.





Step 1Unplug the washing machine, and turn off the water supply to the machine. If necessary, remove the water hoses from the back of the washing machine because they may be in the way of the access panel.





Step 2Check that the agitator is seated correctly by opening the lid of the washing machine. If it's loose, pop off the top of the agitator--if there is one--and tighten the bolt that holds the agitator in place. Or, in some models, simply pull straight up and then reseat the agitator.





Step 3Remove the access panel located in the back of the washing machine by unscrewing the screws holding it in place. This allows access to the drive motor.





Step 4Press on the drive belt that works the agitator. If the belt moves more than 3/4 inch, tighten the belt to fix the spinner problem. If the belt is worn or cracked, replace the belt.





Step 5Replace the drive motor, if tightening or replacing the drive belt doesn't fix the agitator. Purchase a new drive motor at a wholesale retailer. Disconnect wiring, remove screws holding motor in place and insert new motor. Screw into place, and connect wiring.





Step 6Check for any black substance leaking under the washing machine. This might indicate a clutch problem, if the washing machine spinner is not working. Contact a professional repairman to replace the clutch.My whirlpool machine washer wont spin or agitate?
I guess you probably don't have a warranty or something?





If you're mechanically inclined you can take it apart and figure out what's broke in there. Probably a belt or something.





They're not real complicated machines, though they are kind of heavy. And generally full of dust and the occasional spider.





You can check your local directory for places that sell replacement parts if you need them. I can get parts for stuff like that from a place about two miles from here. You'll need to find out your exact make and model to get a matching part.





Otherwise you're going to have to pay somebody to fix it for you, or buy another one.My whirlpool machine washer wont spin or agitate?
Could be the safety switch that completes the circuit when the lid is closed. Most of the time this is where the problem is.

Can i wash or dry my wetsuite in the washer or dryer?

NOOOOO!!





When you bought it, didn't have some manufacturer's instructions with it? Wash it down with fresh tap water from a hose or shower and hang out (preferably not in direct sun) to air dry. DO NOT dry it in a dryer or with any forced hot air, like a hairdryer. You will ruin it real fast if you do.Can i wash or dry my wetsuite in the washer or dryer?
If you live someplace where you cant leave you wetsuit outside (it happens) you can fill the basin in a washing machine with clean cold water and soak your suit. I wouldn't actually use any cycle other than soak. I wouldn't want to agitate the suit. DON'T use detergent. DON';t put it in the dryer. This will run the suit. Detergent is abrasive and the heat will ruin any glued seams you have on it. let it soak, then hang it up out of the sun to dry. If all else fails hang it in your shower.Can i wash or dry my wetsuite in the washer or dryer?
don't! it ruins your wetsuit!


hang it up on a clotheshanger to dry either inside or outside (if it's sunny) and it will be dry or at the most slightly damp by the next day. if it's dirty then rinsing it out with water and giving it a good scrub would be the best- putting it in the washer and dryer would ruin the seams
i dont recomend it at all, just give it a rinse down then hang it somewhere with a good air circulation.


p.s. they was a survey that said that when you pee in your wetsuit in prolonges its life, something to do with the minerals.
NO WAY!!!!!!! You would totally ruin your wetsuit and waste a bunch of money on it. I am guessing that yours is brand new too.





You should rinse it off with fresh water with a hose. Then let it dry on a hangar.
no just hang it on cloathsline and hose it

Can u wash the sham wows cloths in the washer?

Yeah, in the comercials they throw them in the washer...that's what makes them great. you can reuse them and don't just throw them away like paper towels.Can u wash the sham wows cloths in the washer?
Yes! It even says so on the tv commercial.Can u wash the sham wows cloths in the washer?
you can wash it, you can dry it, you can eat it, you can fly it!!!!


Sham Wow! %26lt;now available at walmart, target and most dollars stores. $19.95%26gt;

Is there a screen to catch small debris (ie.earrings) in the kemore He2 plus washer? Where is it located?

Yes theres a screen,,in the lower front..look it up online...its easy to do..i catch a lot of coins there.Is there a screen to catch small debris (ie.earrings) in the kemore He2 plus washer? Where is it located?
It could be caught in the pump filter. Check your owner's manual on how to remove the pump.

I have a washer/dryer set that i need 2 sell~anyone know of a store that buys appliances in S.E. MICHIGAN. ?

both appliances are kenmore...dryer is gas.


thanks Yahoo familyI have a washer/dryer set that i need 2 sell~anyone know of a store that buys appliances in S.E. MICHIGAN. ?
Look in the yellow pages for ';used appliances';I have a washer/dryer set that i need 2 sell~anyone know of a store that buys appliances in S.E. MICHIGAN. ?
you could try putting it in the classified ads thru a newspaper or craigslist. Not sure if they have this store there, but google a search for discount stores for appliances in your area.

worms

Brand new Kenmore washer that won't spin?

I just got my new Kenmore washer today and I've used it twice and it worked fine those two times but on my third load it wouldn't spin. Like the water came out regularly but the washer wouldn't spin. I thought it was over heated or something from being used too much so i waited a couple hours or so and tried again but it still wouldn't spin. I checked the manual and it said the load could be too light but i had the same amount of clothes in there as my last load. help?Brand new Kenmore washer that won't spin?
Return it, plain and simpleBrand new Kenmore washer that won't spin?
They come with warraties. If you are willing to wait a couple days for a repair call the mfr and ask them to set you up with warranty service. Or if you dont want to wait you could ask that the dealer exchange it, but be ready for the to say no. Some dealers will not exchange it because that is what the warranty is for.





Sounds like maybe the lid switch went out?
It sounds like your lid switch is not engaging. For a simple solution, try pushing down on the lid. It might make the switch engage for the time being. Then call Sears and have a service technician come to repair it. It should be a real simple repair that can be handled the same day. You're still in warranty so there should be no charge.
The time you spent asking the question here would have been better spent calling the location where you bought it from. The washer has a warranty and you need to call the place you bought it from and let them know that the machine is not working properly.
Call Sears (KMART) immediately. If they delivered and installed it could be improper installation or you got a defective one. They are normally very good about correcting any issues.
Take it back and ask for a new one. They normally have a few months warranty on them.
exchange it.





no use fixing it if you only used it 3 times and it gave out
Time to take it back!!

I have blue lights that shine out from my washer jets on my car,i was wondering if its legal to do this?

In the UK, the use of any blue light or reflector on any vehicle other than an emergency vehicle is illegal. Only the other week, I saw a car stopped by police for having exactly the type of lights that you describe. The driver had to disconnect them at the roadside before being allowed to continue his journey.I have blue lights that shine out from my washer jets on my car,i was wondering if its legal to do this?
the person who gave you your answer is a man - check profile Report Abuse
I have blue lights that shine out from my washer jets on my car,i was wondering if its legal to do this?
That sounds really good, but I don't think it is legal. But who cares if it looks cool.
Well, it's about time bad taste was outlawed, but I don't think our prisons could hold 60 million people.
impersonating a police car is a serious offence. but i see lots of people doin it so they may not be enforcing it that severely as long as they don't start flashing u should be OK ish. the cop could be having a bad day
Quite simply..if you are in the UK you must not show any Blue light on the outside of your vehicle...IT IS ILLEGAL
no, as long as they don't shine into oncoming vehicles, truck drivers shine a purple light down the windshield from the top to take some of the glare from oncoming headlights, doesn't really help though.
no. Have some self respect and take them off
no they are not legal for use on the public road,


You would be best off installing a switch onto your car so you can show off to your freinds when parked up but when on the road turn them off otherwise the plod may RIP them out, (I have seen this done)
It's certainly not recommendable, and might even be illegal.
Not sure whether it's legal, but it sure sounds tacky.





Who do you think you are Michael Knight?





Get back to Essex and stay there.
I think it depends on your local/state laws. Not all are the same.
I use to have them on my wheels and was told to take them off because any blue light is illegal. I don't know if this is true but you might try looking up state driving laws for your state that should tell you.
legal may depend on where you are but isn't that kinda dumb.
not sure! but i think it looks sh*t sorry! it can cause other cars to have accidents as if you glance in ya miior and just see the blue you think it is an emergency service
Most modding things are marked for show purposes only! The majority of things light blue lights, heavy tints, spinners on wheels etc are classed as road illegal!
I don't think it's legal!
Simple answer. It is illegal to show any lights not required under the Road Traffic Act. That includes fog and spot lights in clear conditions.

Windshield washer repair - 1991 Ford Bronco XLT 4x4?

Any advice on repairing the windshield washer? I replaced the washer pump, checked the hoses and nozzles for obstructions, checked the fuse, and can't find any reason it shouldn't be working. Is there anything I missed checking? And yes the reservoir is full of fluid.Windshield washer repair - 1991 Ford Bronco XLT 4x4?
Check to see if the pump is running when commanded on. If it is, you must have blockage somewhere in the lines or squirters or a leaking line. If the pump does not run, check for power at the pump ( simple test light will work.) If there is power to the pump (and ground) the pump is faulty. If no power and the fuse is good, i would test the switch.